Summer Starts Here - Save up to 70%
TorkLift Wiring Harness Extension Installation - 2005 Ford F-350 Super Duty- Video
Rate your transcript OrderClientKevin BrossRef #20535Order #TC0676263731 Today on our 2005 Ford F350 Super Duty, were going to be installing the TorkLift Wiring Extension for the 32-inch hitch truss extender, part number TLW6032. Now, this vehicle is already equipped with the TorkLift Super Hitch Magnum Hitch along with the SuperTruss Extension. In order to get the wiring from the vehicles plug at the hitch out to the end of the extension, so we can plug into our trailer or towed item, well need a wiring extension. To begin, we need to remove the end of the wiring extension, so we can feed it through the bracket. Then, well reassemble the end, and secure the 7-pull plug here at the end of the extension, and route the other 7-pull plug to the 7-way at the back of the vehicle.To start, well go ahead and remove the plug. First, Im going to back out the fastener that secures the wire here at the end of the plug. more
8/14/2014 11:27:10 AM
Trailer Brake Controller Installation - 2002 Ford F-350- Video
Today on our 2002 Ford F350 well be installing the Tekonsha Prodigy P3 brake controller, part number 90195-3035P in conjunction with our Hopkins seven and four pole vehicle connection point, part number 37185. Our first step will be mounting our Hopkins seven and four pole bracket to our seven and four pole plug. Using the hardware provided with our install kit we can go ahead and insert the screws and secure it with the nuts. Next well move to the vehicle, then we can take a grinder or a cutoff wheel and remove the bracket for the old connector. Then we can go ahead and take our side cutters, cutting zip ties or wires leading up to the connector. Then we can go ahead and cut it off and strip back the wires. more
2/22/2013 10:10:18 AM
Fifth Wheel and Gooseneck Wiring Harness Installation - 2006 Ford F-350- Video
Today on this 2006 Ford F350, well be installing the Pollack T-One connector part number pk11893-11932. We will start off at the bumper of the vehicle where you will find the previously installed 7 pole with a gray locking tab on it. We will undo the lock and pull the 7 pole free, but first we will need to loosen this bracket here for more working room. With everything separated we will start installing the T- One harness and lock it into position. Now that we have made our connections underneath we need to go ahead and drill a hole so that we can mount our connector in the bed. It is recommended that you have a minimum five inch clearance behind where ever you are going to drill. more
11/5/2011 3:52:57 AM
Trailer Brake Controller Installation - 1999 Ford F250- Video
Today we're going to install the Prodigy brake controller from Tekonsha, Part Number 90185, on a 1999 Ford F-250, the light-duty version. This will also apply to the same year Ford F-150. We're going to start off with this one vehicle that only has a factory 4-pole package on it and does not have the 7-pole in the back. So we're going to have to upgrade the 4-pole to make it a 7-pole and then we can install the brake controller up front. The first thing we do is install one of two brackets on the hitch itself so we have a place to mount our electrical connector, and basically we're going to be using Part Number 18140 from Tow-Ready. And basically this is one that clamps in place right here. Basically it's just a hose clamp that goes around the hitch and back through itself. And then you just tighten it down with a clamp set. You might want to hold the bracket in position while you tighten it down, too. Next we're going to install a bracket by a hole in the connector right here. And this comes with the Part Number 37185, and that's a 4-pole to 7- and 4-pole adapter. more
8/27/2008 7:05:40 PM
Filter Videos
Filter Videos
